« previous next »
Pages: [1]   Go Down

Author Topic: What is best to use when cleaning Molex (?) pins  (Read 625 times)

0 Members and 1 Guest are viewing this topic.

Offline Pop Bumper Pete

  • Trade Count: (+4)
  • ******
  • Forum Posts:
    • Ballarat
What is best to use when cleaning Molex (?) pins
« on: May 22, 2012, 06:53:32 PM »
I want to clean the connecting pins on the circuit boards in my Flash Gordon
(I will eventually change the plugs, but that is a job for another day)
What is right cleaning fluid for the job?

Pete
Logged

Offline Strangeways

  • Pinball Restoration is my passion
  • Administrator
  • Trade Count: (+9)
  • *****
  • High Score Initials:
  • Forum Posts:
    • Melbourne
  • ABN 68 283 634 461
    • Ride The Boney Beast
Re: What is best to use when cleaning Molex (?) pins
« Reply #1 on: May 22, 2012, 07:01:14 PM »

Metho or isopropyl alcohol - works a treat.
Logged
Aussie Pinball - Proud to be Australia's Premier Pinball Forum

http://www.australianpinballrestorations.com.au/

http://www.rtbb.com.au/catalog/

We carry the largest range of NEW Ramps in Australia

Offline Pop Bumper Pete

  • Trade Count: (+4)
  • ******
  • Forum Posts:
    • Ballarat
Re: What is best to use when cleaning Molex (?) pins
« Reply #2 on: May 22, 2012, 07:19:17 PM »
thanks
Logged

Offline Homepin

  • Trade Count: (+15)
  • ******
  • Forum Posts:
  • Not a business - A Passion!
Re: What is best to use when cleaning Molex (?) pins
« Reply #3 on: May 22, 2012, 07:21:55 PM »
C'mon - get that POS going will ya'  <..>
Logged
Replacement Pinball PCBs that remain faithful to the originals

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Re: What is best to use when cleaning Molex (?) pins
« Reply #4 on: May 22, 2012, 07:57:01 PM »
I also put the female side in a bowl.. sprinkle some Bicarb over them and then vinegar... fizzes up and takes off a lot of the grime inside... make sure you rinse off and dry well before connecting again though
Logged

Offline Homepin

  • Trade Count: (+15)
  • ******
  • Forum Posts:
  • Not a business - A Passion!
Re: What is best to use when cleaning Molex (?) pins
« Reply #5 on: May 22, 2012, 08:01:42 PM »
Quote from: Retropin on May 22, 2012, 07:57:01 PM
I also put the female side in a bowl.. sprinkle some Bicarb over them and then vinegar... fizzes up and takes off a lot of the grime inside... make sure you rinse off and dry well before connecting again though

I do that as well but they tend to scream and wriggle about a lot - - - oh wait, you mean connectors.......I see.........
Logged
Replacement Pinball PCBs that remain faithful to the originals

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Re: What is best to use when cleaning Molex (?) pins
« Reply #6 on: May 22, 2012, 08:14:27 PM »
Quote from: Homepin on May 22, 2012, 08:01:42 PM
Quote from: Retropin on May 22, 2012, 07:57:01 PM
I also put the female side in a bowl.. sprinkle some Bicarb over them and then vinegar... fizzes up and takes off a lot of the grime inside... make sure you rinse off and dry well before connecting again though

I do that as well but they tend to scream and wriggle about a lot - - - oh wait, you mean connectors.......I see.........

LOL- too funny  %.% %.%
Logged

Offline Pop Bumper Pete

  • Trade Count: (+4)
  • ******
  • Forum Posts:
    • Ballarat
Re: What is best to use when cleaning Molex (?) pins
« Reply #7 on: March 29, 2015, 06:15:32 PM »
OK, another game, same problem

pulled an old game out of storage, only a handful of lamps worked
I have used metho, and got a few more going
but the pins look like they are still dirty

will a dremel and a cutting compound clean them up?
(open to other suggestions before I replace them)
Logged

Offline RatBag

  • Trade Count: (+1)
  • *****
  • Forum Posts:
    • Perth
Re: What is best to use when cleaning Molex (?) pins
« Reply #8 on: March 29, 2015, 06:43:53 PM »
Get your self one of these,also good for cleaning up pads before soldering
http://www.ebay.com.au/itm/Fiberglass-Pen-Fibre-Pencil-Abrasive-Cleaning-PCBs-Etc-/190384502242
Logged

Offline studley67

  • Trade Count: (+7)
  • ******
  • Forum Posts:
    • adelaide hills
    • facebook
Re: What is best to use when cleaning Molex (?) pins
« Reply #9 on: April 03, 2015, 09:47:28 PM »
Quote from: Homepin on May 22, 2012, 08:01:42 PM
Quote from: Retropin on May 22, 2012, 07:57:01 PM
I also put the female side in a bowl.. sprinkle some Bicarb over them and then vinegar... fizzes up and takes off a lot of the grime inside... make sure you rinse off and dry well before connecting again though

I do that as well but they tend to scream and wriggle about a lot - - - oh wait, you mean connectors.......I see.........
rotflmao
Logged
Life is too short to spend time with people who suck the happiness out of you

Offline studley67

  • Trade Count: (+7)
  • ******
  • Forum Posts:
    • adelaide hills
    • facebook
Re: What is best to use when cleaning Molex (?) pins
« Reply #10 on: April 03, 2015, 09:49:00 PM »
good to see pete is replacing the connectors @@*
Logged
Life is too short to spend time with people who suck the happiness out of you

Offline Mr Pinbologist

  • Trade Count: (+5)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Wauchope NSW
Re: What is best to use when cleaning Molex (?) pins
« Reply #11 on: April 03, 2015, 11:13:16 PM »
Quote from: RatBag on March 29, 2015, 06:43:53 PM
Get your self one of these,also good for cleaning up pads before soldering
http://www.ebay.com.au/itm/Fiberglass-Pen-Fibre-Pencil-Abrasive-Cleaning-PCBs-Etc-/190384502242

Thanks for the link  ^^^ ^^^ these things are GREAT, my old boss used to have one!!
Logged
Pages: [1]   Go Up
« previous next »