Handy hints and tips

Pages: 1 ... 3 4 [5] 6 7 ... 12 Go Down

	Subject / Started by	Replies / Views / Likes	Last post
0 Members and 5 Guests are viewing this board.
	DMD newbie Question Started by Kano	3 Replies 903 Views / 0 Likes	November 19, 2012, 05:23:50 AM by Homepin
	Simple drop target fix, you’ll be surprised! Started by Kirk332	0 Replies 1970 Views / 0 Likes	October 30, 2018, 03:32:05 AM by Kirk332
	How To Flame Polish Ramps Started by ktm450 « 1 2 »	23 Replies 3824 Views / 0 Likes	July 07, 2011, 02:27:22 AM by pokermachine
	Repairing vacuum formed plastics (WH20, IJ etc) Started by ktm450	13 Replies 693 Views / 0 Likes	June 16, 2009, 04:06:54 PM by ktm450
	Re-bluing ramp flaps Started by ktm450 « 1 2 »	15 Replies 1828 Views / 0 Likes	June 15, 2009, 04:06:41 PM by Strangeways
	Reusing Decals when replacing ramps etc. Started by ktm450 « 1 2 »	26 Replies 5510 Views / 0 Likes	August 01, 2013, 07:15:59 PM by Crashramp
	Playfield Restoration - Roll over switch tip Started by ktm450 « 1 2 »	17 Replies 1322 Views / 0 Likes	May 29, 2009, 12:37:54 AM by ajlaird
	Bally em ( Camelot) 1 point relay energizes and stays on, until turned off. Started by lanternau	11 Replies 2045 Views / 0 Likes	February 16, 2014, 11:37:22 AM by ddstoys
	TIP - A missing power supply that isn't missing. Started by Marty Machine	0 Replies 411 Views / 0 Likes	April 22, 2009, 01:27:38 AM by Marty Machine
	How do i flatten-out plastics???? Started by Marty Machine « 1 2 »	18 Replies 1055 Views / 0 Likes	May 27, 2009, 10:29:03 PM by studley67
	Buy yourself a cheap CRO for board testing Started by Marty Machine	12 Replies 1295 Views / 0 Likes	May 31, 2009, 11:45:12 AM by Marty Machine
	Swap-Over of Parts+Wiring between 2 playfields?? Started by Marty Machine « 1 2 »	15 Replies 1407 Views / 0 Likes	December 11, 2009, 12:01:01 AM by Marty Machine
	[Tech Tip #10] Measuring I.C pins. Started by Marty Machine	0 Replies 441 Views / 0 Likes	June 15, 2011, 08:46:25 PM by Marty Machine
	Where do i get LONG lengths/rolls of braid-wire for under Playfield (GI) wiring? Started by Marty Machine « 1 2 3 »	30 Replies 1570 Views / 0 Likes	December 16, 2009, 11:16:16 AM by Marty Machine
	Williams Sys-6 (or other) Sound Board Sound Rom info ????? Started by Marty Machine	4 Replies 1146 Views / 0 Likes	December 07, 2008, 06:45:23 PM by humpalot
	[Tech Tip #11] Confirm Voltages. Started by Marty Machine	0 Replies 506 Views / 0 Likes	June 15, 2011, 08:58:12 PM by Marty Machine
	[Tech Tip #12] Faulty ROMs - Be Afraid!! Started by Marty Machine	8 Replies 1449 Views / 0 Likes	June 18, 2011, 01:01:54 PM by The pinballist formally known as Dean Morgan
	Replace your old DMD - Notice any differences ????? Started by Marty Machine	3 Replies 466 Views / 0 Likes	July 15, 2009, 11:48:26 PM by Marty Machine
	[Tech Tip #13] Power Supply Distribution. Started by Marty Machine	0 Replies 460 Views / 0 Likes	June 15, 2011, 09:28:20 PM by Marty Machine
	Coil Standards? what goes where??? Started by Marty Machine	13 Replies 1096 Views / 0 Likes	June 13, 2009, 01:13:42 PM by Pinlinds

Pages: 1 ... 3 4 [5] 6 7 ... 12 Go Up

Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)

Locked Topic
Sticky Topic
Poll

News: