« previous next »
Pages: [1]   Go Down

Author Topic: Flash Gordon flipper problem  (Read 261 times)

0 Members and 1 Guest are viewing this topic.

Offline Crashramp

  • Trade Count: (+3)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Albury
Flash Gordon flipper problem
« on: November 21, 2014, 02:31:27 PM »
Hi Guys,

I was having a game on my Flash Gordon machine a few days ago when the 2 right hand side flippers died on me. I've checked all fuses and even swapped them out just to be sure as well as checked the cabinet switches and re seated connectors in the Headbox. Wiring to the coils is also fine and intact. Any ideas? Thanks.
Logged

Offline Pintoxicated

  • Trade Count: (+9)
  • ******
  • Forum Posts:
    • Table Top - Albury NSW
Re: Flash Gordon flipper problem
« Reply #1 on: November 21, 2014, 02:59:15 PM »
Ahhh, another machine that needs to spend time at my place I think.
Logged
Addicted to pins.

Offline PinPal

  • Trade Count: (0)
  • ******
  • Forum Posts:
    • Sydney, Australia
  • Pinpal Pinball
Re: Flash Gordon flipper problem
« Reply #2 on: November 21, 2014, 06:32:23 PM »
Quote from: Crashramp on November 21, 2014, 02:31:27 PM
Hi Guys,

I was having a game on my Flash Gordon machine a few days ago when the 2 right hand side flippers died on me. I've checked all fuses and even swapped them out just to be sure as well as checked the cabinet switches and re seated connectors in the Headbox. Wiring to the coils is also fine and intact. Any ideas? Thanks.
Hope it something simple, haven't had any thing like that happen to my FG, might be something on the power board.
Pinpal....
Logged

Offline Ballywannabe

  • Trade Count: (0)
  • *****
  • Forum Posts:
    • Perth
Re: Flash Gordon flipper problem
« Reply #3 on: November 21, 2014, 09:34:59 PM »
Things to check for:

EOS switch on the bottom flipper not making contact (most likely, try pushing it together while activating the flipper button - watch your fingers!)
Blown lower flipper coil (check resistance and compare with the working flipper)
Cabinet switch not making contact (contacts can 'fall out' of the blade)
Bad connector on the SDB - check the schematics and see where the power for the lower flipper comes from

hope this helps!
Logged

Offline Crashramp

  • Trade Count: (+3)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Albury
Re: Flash Gordon flipper problem
« Reply #4 on: November 21, 2014, 11:53:38 PM »
Quote from: Ballywannabe on November 21, 2014, 09:34:59 PM
Things to check for:

EOS switch on the bottom flipper not making contact (most likely, try pushing it together while activating the flipper button - watch your fingers!)
Blown lower flipper coil (check resistance and compare with the working flipper)
Cabinet switch not making contact (contacts can 'fall out' of the blade)
Bad connector on the SDB - check the schematics and see where the power for the lower flipper comes from

hope this helps!

Thanks for that, I'll work my way through your suggestions tomorrow. I need to get a new multimeter as well, It's not reading correctly.
Logged

Offline riverinapinball

  • Trade Count: (0)
  • *****
  • Forum Posts:
Re: Flash Gordon flipper problem
« Reply #5 on: November 22, 2014, 09:20:51 AM »
Bad batterys in a multimeter will make it give weird readings.
Logged

Offline Crashramp

  • Trade Count: (+3)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Albury
Re: Flash Gordon flipper problem
« Reply #6 on: November 22, 2014, 10:59:19 AM »
Quote from: riverinapinball on November 22, 2014, 09:20:51 AM
Bad batterys in a multimeter will make it give weird readings.

Thanks Dan, I hadn't thought of that. I'll give it a go before I chuck it over the fence.
Logged
Pages: [1]   Go Up
« previous next »