Author Topic: Edge connector contact remover  (Read 2281 times)

0 Members and 1 Guest are viewing this topic.

Offline Crashramp

  • Trade Count: (+3)
  • ******
  • High Score Initials:
  • Forum Posts:
  • Albury
Edge connector contact remover
« on: July 29, 2017, 06:16:47 PM »
Hi Guy's,


What do people use to remove the contacts from edge connectors? The 21 pin connectors used on system 1 pins don't seem to be available anymore so I need to reuse the connector and I'm having a bastard of a time trying to get them out.

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Re: Edge connector contact remover
« Reply #1 on: July 29, 2017, 08:27:28 PM »
You gradually remove them by lifting one side then the other.. bit by bit they come away.

Offline Crashramp

  • Trade Count: (+3)
  • ******
  • High Score Initials:
  • Forum Posts:
  • Albury
Re: Edge connector contact remover
« Reply #2 on: July 29, 2017, 09:25:15 PM »
Thanks Gav,
 I had filed down a piece of piano wire so it fits in the pcb side of the connector but haven't tried lifting the contact from both sides. Do you use a specific tool?

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Re: Edge connector contact remover
« Reply #3 on: July 29, 2017, 10:12:04 PM »
Yes - fingers

Offline Crashramp

  • Trade Count: (+3)
  • ******
  • High Score Initials:
  • Forum Posts:
  • Albury
Re: Edge connector contact remover
« Reply #4 on: July 29, 2017, 11:28:48 PM »
Thanks Gav but it's the contact pins inside the connector housing that I'm trying to remove so that I can re-pin the wires and reuse the housing. Removing the connectors from the board is no problem.

Offline Steevsee

  • Trade Count: (+1)
  • ******
  • High Score Initials:
  • Forum Posts:
  • Brisbane
Re: Edge connector contact remover
« Reply #5 on: July 30, 2017, 12:23:38 AM »
You have to push them in slightly when inserting the tool and then pull them out.  The lock tab tends to wedge against the plastic of the housing if you  try to pull them straight out.

Offline Crashramp

  • Trade Count: (+3)
  • ******
  • High Score Initials:
  • Forum Posts:
  • Albury
Re: Edge connector contact remover
« Reply #6 on: July 30, 2017, 08:15:27 AM »
Thanks, I think I've been pulling at the wire rather than pushing it in first.

Offline pinnies4me

  • Administrator
  • Trade Count: (+5)
  • *****
  • High Score Initials:
  • Forum Posts:
  • Victoria
Re: Edge connector contact remover
« Reply #7 on: July 30, 2017, 08:58:25 AM »
There is a tool for this, but I find it easy to push the wire inwards a little, then through the gap in the connector where the tab on the pin ends up, using a tiny flat edge screwdriver, bend the tab down, and then the lot will just pull out.
“If you wanna escape, go up to a pinball machine. There’s a magic button on the front that takes you to a world under the glass and makes the the rest of the universe disappear.”

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Re: Edge connector contact remover
« Reply #8 on: July 30, 2017, 09:54:16 AM »
Ha ha!!! - I thought you were trying to get them off the board..LOL.
But yes, as stated before... push the tab of the clip in quite hard and pull out.

Offline Strangeways

  • Pinball Restoration is my passion
  • Administrator
  • Trade Count: (+9)
  • *****
  • High Score Initials:
  • Forum Posts:
  • Melbourne
  • ABN 68 283 634 461
    • Ride The Boney Beast
Re: Edge connector contact remover
« Reply #9 on: July 30, 2017, 10:25:52 AM »

There is a tool, but it breaks easily if you use it a lot.

Go and buy a cheap jewelers' screwdriver set and grind the tip so it is thin enough to fit in the cavity where the tab on the metal clip is. Simply push the tab down with the screwdriver, and pull it out. In a pinch I use a nail - much quicker than using the tool designed to do the job !
Aussie Pinball - Proud to be Australia's Premier Pinball Forum

http://www.australianpinballrestorations.com.au/

http://www.rtbb.com.au/catalog/

We carry the largest range of NEW Ramps in Australia

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Re: Edge connector contact remover
« Reply #10 on: July 30, 2017, 10:41:34 AM »

There is a tool, but it breaks easily if you use it a lot.

Go and buy a cheap jewelers' screwdriver set and grind the tip so it is thin enough to fit in the cavity where the tab on the metal clip is. Simply push the tab down with the screwdriver, and pull it out. In a pinch I use a nail - much quicker than using the tool designed to do the job !

That's right.. my tool bent over on the first go. Used a tiny screwdriver instead

Offline Crashramp

  • Trade Count: (+3)
  • ******
  • High Score Initials:
  • Forum Posts:
  • Albury
Re: Edge connector contact remover
« Reply #11 on: July 30, 2017, 02:19:23 PM »
Thanks for all of the replys guys. Very helpful.   ^^^

Offline riverinapinball

  • Trade Count: (0)
  • *****
  • Forum Posts:
Re: Edge connector contact remover
« Reply #12 on: July 30, 2017, 04:28:21 PM »
Here are some pics of a tool i picked up a while ago , works fine.










Sent from my iPhone using Tapatalk

Offline Crashramp

  • Trade Count: (+3)
  • ******
  • High Score Initials:
  • Forum Posts:
  • Albury
Re: Edge connector contact remover
« Reply #13 on: July 30, 2017, 07:34:42 PM »
Thanks Dan.  ^^^