Aussie Pinball Forums > Restorations

Bally Dr Who High End Restoration

(1/8) > >>

Strangeways:
A collector that I've done a couple machines - just standard restorations, has taken the plunge with his "Holy Grail" - The Bally Dr Who. Much underrated title. Similar to the Addams I'm doing, this is a "NIB" (Nearly In Box) Restoration.

Condition report

Cabinet - Not too bad, but we are using the skills of Tim and Stu to make a new cabinet.
Playfield - 8/10 - A VERY nice example. Again, off to Tim for a Clearcoat.
Electronics - 8/10 - Honest boardset. No major dramas.

This is another long term project that has taken quite some time to gather all the necessary components to ensure the NIB standard we pride ourselves on. The ramps will be replaced with the Starship Fantasy Ramp Set. Colour DMD will be used and some more additional items as we progress.

Before pictures and teardown



OK Cabinet - But we are having a new one made for this restoration. But we will re purpose this cabinet for another project..


Playfield is removed as the cabinet had to be sent to Tim for final measurements on the new cabinet. So I have a bit of time to strip the playfield. Given I lost all my teardown pictures of the other Dr Who games I've done, I needed to document the process again.











The inserts in front of the time expander are ALWAYS a problem with significant wear. They are often sunken, or have the clear completely chipped out. Not this game. The playfield is excellent.








Time Expander mini pf is in really good shape.





Filthy !





Under the playfield - REALLY good condition.











I get asked this question A LOT - "how do you know where things go when you reassemble ? " - I take HUNDREDS of photos, of every angle, and measure out all the spacers etc.. The caliper comes in handy for this process. Patience and good record keeping provides a good reference. The only exception is Addams Family. I've done that many, I know where everything goes without photos !








Here is my left handed screwdriver, next to my right handed screwdriver..

One for 1/4 hex heads and the other is a phillips head.





Just the cable management parts left to remove.





Every single mech is reordered, rebuilt and then refitted.





All the parts are cleaned in the ultrasonic, and then tumbled first in a rough media tumbler and then for a final polish in a finer grade media tumbler. Anything worn or broken, is replaced.

While this is happening, look what arrives - The new cabinet, courtesy of Tim and Stu..








Just LOOK at those colours !





Stay tuned !

coon82:
 Maybe my comment in as conflict of interest  &&  but I'm really looking forward to this thread unfold. The pictures of the cabinet don't do it justice *.* () ^^^


 :pinball:

Strangeways:
Way behind updates on this restoration.

I need to finish off the cabinet so I can concentrate on the playfield returned from @el_timbo86 . The decision was made to install the Mantis Cabinet protectors, which are the recommended cabinet protectors I use for High End Games. Nothing wrong with alternatives, but these are exceptional in quality. First, I want to install the Ground braid. I've covered this in the Addams Family thread, so here is this cabinet completed ;









I decided to that the ground braid should go behind the brackets, even though this is not what they did in the factory, I've seen enough broken braid to suggest this is a better method.









Ground braid and leg brackets done.

Strangeways:
Here are some of the new cabinet parts installed, or are about to be installed. I don't muck around with the original parts on some restorations, opting to use new parts and use my time in other aspects of the restoration.






A more recent development is the use of metal cabinet protectors. They effectively can replace Pincabs or felt leg protectors. The idea here is to protect the Cabinet - not the legs. I've used most metal protectors on the market, but I much prefer the Mantis version, as it is thicker and has four mounting holes. The other advantage is that they have a polished edge.





3mm Thick. The thickest protector I've seen.






They are EASY to install. First - position them with clearance through the cabinet leg bolt holes.





Pre Drill the first hole ;






Screw the first wood screw in position, but do not tighten





Ensure both bolts are easily installed and removed by hand.










Drill one hole on the opposite side of the protector and tighten both screws into the cabinet. Once everything is set up correctly, measure the distance between the bottom of the cabinet and the metal protector.





Transfer that to the other side..






Follow the same procedure as the first protector..






Then follow the same procedure as the rear - although the distance from the bottom of the cabinet will be different.








Next update - playfield..

Strangeways:
Overdue update.

I like to be working on several restorations so I can do work in batches. This time, this update will concentrate on the finer details of the playfield underside - in particular the Zinc Plating that I've been doing in-house for years with success.


The power box has a zinc plated galvanized finished which is practical but looks out of place on a High End Restoration. I thought I'd try something new and attempt to plate the power box and also the power cable box located on the rear panel. So here is the starting point ;








The two items are put aside and prepped with a lot of other parts for different games that I will Zinc Plate. Here is the 30 Liter tub of magical solution busy at work in mt chemical laboratory..






After plating, here are the results ;








Re assembly ;






More plating during this session ;













The DR Who VUK Assembly ;





The "Time Expander" assembly looks completely different after plating ;

Navigation

[0] Message Index

[#] Next page