Author Topic: Coil Help  (Read 408 times)

0 Members and 2 Guests are viewing this topic.

Offline ktm450

  • Trade Count: (+1)
  • ******
  • High Score Initials:
  • Forum Posts:
  • Geelong, Victoria
Coil Help
« on: July 20, 2009, 01:15:26 PM »
After a discussion with Nick the other night whilst playing Whitewater I decided to check my Lost mine kickout coil as it fires the ball out too fast, straight at the metal ball guide above the right flipper. 
Occasionally so hard it can go back into the lost mine and get kicked out again   @.@


The manual states an AE23-800

My pin has a AE23-800-3

going by BAA the AE23-800 is a coil without a diode
http://bayareaamusements.com/Merchant2/merchant.mvc?Screen=PROD&Product_Code=WC-23-800&Category_Code=

and the AE-23-800-3 is a coil with a diode
http://bayareaamusements.com/Merchant2/merchant.mvc?Screen=PROD&Product_Code=WC-23-800-03&Category_Code=

There are several that size with different numbers (ie. -1, -2, -3, -4, etc.)

What does this number corespond too? Is this my problem?

Thanks,
Matt.

Offline ktm450

  • Trade Count: (+1)
  • ******
  • High Score Initials:
  • Forum Posts:
  • Geelong, Victoria
Re: Coil Help
« Reply #1 on: July 20, 2009, 01:27:23 PM »
Just had another look at it, the diode has been removed anyway so it should perform the same as the original.
Do any other WH20 owners have this problem?
Before I rebuilt it, it must have been aimed slightly different, as the ball used to hit the top of the flipper then roll up the inlane and back down (good for spotting river letters)
Maybe I just need to adjust the aim of it, but it is still way over powered  !@#

Maybe a 24-900 coil?
« Last Edit: July 20, 2009, 01:32:10 PM by ktm450 »

Offline Strangeways

  • Pinball Restoration is my passion
  • Administrator
  • Trade Count: (+9)
  • *****
  • High Score Initials:
  • Forum Posts:
  • Melbourne
  • ABN 68 283 634 461
    • Ride The Boney Beast
Re: Coil Help
« Reply #2 on: July 20, 2009, 01:32:27 PM »

Matt - Measure the resistance of the coil - this will tell you if the coil is defective. I think not - but it is worth a shot.

The assembly itself could be out of adjustment ? If the plunger is too short - it travels further, thus becoming more powerful. When you shopped the game - did you replace the plunger with a shorter one perhaps ?
Aussie Pinball - Proud to be Australia's Premier Pinball Forum

http://www.australianpinballrestorations.com.au/

http://www.rtbb.com.au/catalog/

We carry the largest range of NEW Ramps in Australia

Offline ktm450

  • Trade Count: (+1)
  • ******
  • High Score Initials:
  • Forum Posts:
  • Geelong, Victoria
Re: Coil Help
« Reply #3 on: July 20, 2009, 01:38:55 PM »

Matt - Measure the resistance of the coil - this will tell you if the coil is defective. I think not - but it is worth a shot.

The assembly itself could be out of adjustment ? If the plunger is too short - it travels further, thus becoming more powerful. When you shopped the game - did you replace the plunger with a shorter one perhaps ?

Nah, didn't replace the plunger (it's actually a cup) all original.

Offline ktm450

  • Trade Count: (+1)
  • ******
  • High Score Initials:
  • Forum Posts:
  • Geelong, Victoria
Re: Coil Help
« Reply #4 on: July 20, 2009, 01:53:33 PM »
Coil tested good too

Offline MartyJ

  • Trade Count: (+4)
  • ******
  • High Score Initials:
  • Forum Posts:
  • Melbourne
Re: Coil Help
« Reply #5 on: July 20, 2009, 05:52:57 PM »
I recall a thread on RGP with people putting a lower strength coil in the WH20 to stop this problem...

I'll see if I can find it.

Offline ktm450

  • Trade Count: (+1)
  • ******
  • High Score Initials:
  • Forum Posts:
  • Geelong, Victoria
Re: Coil Help
« Reply #6 on: July 20, 2009, 06:11:36 PM »
I recall a thread on RGP with people putting a lower strength coil in the WH20 to stop this problem...

I'll see if I can find it.

Yeah, that is prob the easiest way.
I'll have to pick one up from Mark on Saturday (got any 24-900 coils Mark?)

Offline pinnies4me

  • Administrator
  • Trade Count: (+5)
  • *****
  • High Score Initials:
  • Forum Posts:
  • Victoria
Re: Coil Help
« Reply #7 on: July 20, 2009, 06:37:03 PM »
The suggested fix is to replace the 23-800 coil with a 26-1200.
“If you wanna escape, go up to a pinball machine. There’s a magic button on the front that takes you to a world under the glass and makes the the rest of the universe disappear.”

Marty Machine

  • Guest
  • Trade Count: (0)
Re: Coil Help
« Reply #8 on: July 20, 2009, 09:10:56 PM »
I just looked inside my WW, but my coil had no wrapper-paper on it.  !!!
Sorry i couldn't help out.  #@#

FYI: My 'Lost Mine chute' shoots the ball straight onto the right flipper, everytime.
MM.
« Last Edit: July 20, 2009, 09:12:58 PM by Marty Machine »

Offline ktm450

  • Trade Count: (+1)
  • ******
  • High Score Initials:
  • Forum Posts:
  • Geelong, Victoria
Re: Coil Help
« Reply #9 on: July 21, 2009, 04:03:30 PM »
Thanks guys  *%*