« previous next »
Pages: [1]   Go Down

Author Topic: Williams Flash  (Read 896 times)

0 Members and 1 Guest are viewing this topic.

Offline pinfrog

  • Trade Count: (0)
  • ****
  • Forum Posts:
    • Perth WA
Williams Flash
« on: January 27, 2016, 01:41:39 PM »
Hi to all, I have just turned on my Flash and noticed the bottom line of displays 1, 2 and the credit display are not working. Any ideas what could be the problem? I am a bit of a noob in the electronic side of things . Thanks in advance .  Cheers Les.
Logged

Offline Gemini2544

  • Trade Count: (0)
  • ***
  • High Score Initials:
  • Forum Posts:
    • Wimmera Victoria
  • Latest restore "Top Score" Two plater EM
Re: Williams Flash
« Reply #1 on: January 27, 2016, 03:01:44 PM »
Before anything turn off the power & remove & carefully reseat the PCB plugs.  Then power on, report back what happened.
Logged
My collection- Gottleib "Wild life", "Gottleib "Top Score", Gottleib "Target Alpha", Gottleib "Cleopatra", Williams "Space Mission", Williams "Pin*Bot", Bally "Black-Rose" JJP "WOZ" & Chicago Coin "Fun land" Rifle.

Offline pinfrog

  • Trade Count: (0)
  • ****
  • Forum Posts:
    • Perth WA
Re: Williams Flash
« Reply #2 on: January 27, 2016, 06:40:21 PM »
Reseated all plugs but still missing the bottom line. Cheers Les.
Logged

Offline Gemini2544

  • Trade Count: (0)
  • ***
  • High Score Initials:
  • Forum Posts:
    • Wimmera Victoria
  • Latest restore "Top Score" Two plater EM
Re: Williams Flash
« Reply #3 on: January 27, 2016, 07:07:23 PM »
Can you post a pix of the display so we can see the fault please.
Logged
My collection- Gottleib "Wild life", "Gottleib "Top Score", Gottleib "Target Alpha", Gottleib "Cleopatra", Williams "Space Mission", Williams "Pin*Bot", Bally "Black-Rose" JJP "WOZ" & Chicago Coin "Fun land" Rifle.

Offline Gemini2544

  • Trade Count: (0)
  • ***
  • High Score Initials:
  • Forum Posts:
    • Wimmera Victoria
  • Latest restore "Top Score" Two plater EM
Re: Williams Flash
« Reply #4 on: January 27, 2016, 08:51:03 PM »
A mate suggests you check R4 (Resistor #4) on the master display board. Its most probably a charcoal blob.
Logged
My collection- Gottleib "Wild life", "Gottleib "Top Score", Gottleib "Target Alpha", Gottleib "Cleopatra", Williams "Space Mission", Williams "Pin*Bot", Bally "Black-Rose" JJP "WOZ" & Chicago Coin "Fun land" Rifle.

Offline spacejam0

  • Trade Count: (0)
  • ******
  • Forum Posts:
Re: Williams Flash
« Reply #5 on: January 27, 2016, 09:19:00 PM »
Quote from: Gemini2544 on January 27, 2016, 08:51:03 PM
A mate suggests you check R4 (Resistor #4) on the master display board. Its most probably a charcoal blob.
yeah I had a similar issue with my Flash display and it turned out to be a resistor on the master display I can't remember which one but it was easy to spot because you could see it was burnt
Logged

Offline ralph67

  • Trade Count: (+1)
  • *****
  • Forum Posts:
    • Stoneville
    • ralph1967@optusnet.com.au
Re: Williams Flash
« Reply #6 on: January 30, 2016, 05:56:44 AM »
The Resistors are 10K.  Check resistance or R1 to R14 with MM , should read 10K  give or take 10%
 If they need replacing use a 1/2 watt instead of the original 1/4 watt.
Failing that it may be a Chip on the master board .
Logged
One-Ball!
Pages: [1]   Go Up
« previous next »