System 1 connectors

[Crashramp]

Hi guys, where do I find Connectors used on Gottlieb system 1 machines? I've just started some pre restoration clean up work on my Count-down machine and I'd like to replace the display and board connectors but I'm not sure where I can buy them. Thanks in advance.





Sent from my iPad using Tapatalk

[pinnies4me]

I usually keep the connectors and replace the pins. Rtbb has some.

http://www.rtbb.com.au/catalog/product_info.php?products_id=1407

For the driver to cpu interconnect you must get one of these as saves heaps of work, look for sys 1/ sys80 harnesses on left pane

http://www.bigdaddy-enterprises.com

[Crashramp]

I usually keep the connectors and replace the pins. Rtbb has some.

http://www.rtbb.com.au/catalog/product_info.php?products_id=1407

For the driver to cpu interconnect you must get one of these as saves heaps of work, look for sys 1/ sys80 harnesses on left pane

http://www.bigdaddy-enterprises.com

Thanks Nick,

I didn't realise that these were the .156 pins. I have plenty of them but I'd still like to buy new connectors if they're available somewhere. I also have a new Pascal 4 in 1 board to install down the track. It's packed away in a cupboard at the moment so I haven't had much of a look at it yet. Will I still need the interconnecting board to board harnesses with the 4 in 1?

[pinnies4me]

No mate, the four in one won't need that.

[Crashramp]

No mate, the four in one won't need that.

Great, thanks

[pinnies4me]

Just realised the pins on RTBB are the modern ones, you actually need the .156" "card edge" pins.

[Crashramp]

Just realised the pins on RTBB are the modern ones, you actually need the .156" "card edge" pins.

Ok, thanks.

[Crashramp]

I think these are the correct Gottlieb card edge pins. can anyone confirm please?

https://www.greatplainselectronics.com/proddetail.asp?prod=08-52-0072&cat=81

[Mr Pinbologist]

I think these are the correct Gottlieb card edge pins. can anyone confirm please?

https://www.greatplainselectronics.com/proddetail.asp?prod=08-52-0072&cat=81

Pretty sure that they're the correct ones,

These are what i've been using;

http://www.altronics.com.au/p/p5640a-oupiin-crimp-pin-3.96mm-suit-p-5642-p-5660-single/

[Strangeways]

We have limited stock (RTBB) but today - we ordered Gottlieb Connectors, pins and extraction tools. Should be here in 10 days 

[Crashramp]

I think these are the correct Gottlieb card edge pins. can anyone confirm please?

https://www.greatplainselectronics.com/proddetail.asp?prod=08-52-0072&cat=81

Pretty sure that they're the correct ones,

These are what i've been using;

http://www.altronics.com.au/p/p5640a-oupiin-crimp-pin-3.96mm-suit-p-5642-p-5660-single/

Thanks for confirming. 

We have limited stock (RTBB) but today - we ordered Gottlieb Connectors, pins and extraction tools. Should be here in 10 days 

Great Timing! I'll wait till you have them in stock.

[Retropin]

If you are going to replace the connectors, do yourself a great favour at the same time and put some diodes on the return paths for all the coils. They will block any backwash from a locked on coil etc and protect those precious and obsolete spider chips

[Crashramp]

If you are going to replace the connectors, do yourself a great favour at the same time and put some diodes on the return paths for all the coils. They will block any backwash from a locked on coil etc and protect those precious and obsolete spider chips

Thanks Gav, I have a 4 in 1 board to go in so that should take care of that. The machine as I brought it was not in any condition to fire up so at the moment I don't know if there are issues with the existing driver board. I just thought the 4 in 1 would be easier in the long run.