« previous next »
Pages: [1] 2   Go Down

Author Topic: Police force GI issues  (Read 972 times)

0 Members and 1 Guest are viewing this topic.

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Police force GI issues
« on: September 19, 2015, 07:05:19 PM »
Noticed I had no lights working under my slings and few other plastics
 Replaced globes and checked fuses.
I thought I would take a look at interconnect board. Unplugged J12 and the lights worked. Looked throug manual and realised one wire was in the wrong spot on the plug so I corrected it. It now seems I am missing a black violet wire for this plug.

Also looked at J11 and manual only shows 5 wires but i have way more than that on this plug.

Help!!!
Logged

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re:
« Reply #1 on: September 20, 2015, 12:00:38 PM »
P.s topper and red strobes dont work
Logged

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re:
« Reply #2 on: September 20, 2015, 01:29:28 PM »
Bloody Outholes just stopped working!!!!
Logged

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re:
« Reply #3 on: September 28, 2015, 09:14:44 PM »
Bumping this thread. Any ideas why half of my coils are not working? Outhole (drain hole) and two kickers. Slings are working
Logged

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re:
« Reply #4 on: September 28, 2015, 09:50:54 PM »
No coils work.  Just flippers and ball shooter.
Logged

Offline beaky

  • Trade Count: (+7)
  • ******
  • Forum Posts:
    • Melbourne, Vic
Re: Police force GI issues
« Reply #5 on: September 28, 2015, 10:38:14 PM »
do a solenoid test and see if any coils are firing or flashers
sounds like you have lost your 50v dc so check fuse F7 on the Aux driver board
if flippers are working then check F4
« Last Edit: September 28, 2015, 10:42:18 PM by beaky »
Logged
On site pinball repairs in MELBOURNE NTH SUBURBS  : Circuit board repairs and refurbishing Australia wide (via Aust post)

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re:
« Reply #6 on: September 28, 2015, 11:04:56 PM »
Fuses replaced just on case.  Same issue
Logged

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re:
« Reply #7 on: September 28, 2015, 11:05:51 PM »
No coils firing on test. Flashers work.
Logged

Offline beaky

  • Trade Count: (+7)
  • ******
  • Forum Posts:
    • Melbourne, Vic
Re: Police force GI issues
« Reply #8 on: September 28, 2015, 11:07:07 PM »
flippers still working?
Logged
On site pinball repairs in MELBOURNE NTH SUBURBS  : Circuit board repairs and refurbishing Australia wide (via Aust post)

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re:
« Reply #9 on: September 28, 2015, 11:09:34 PM »
Yep
Logged

Offline beaky

  • Trade Count: (+7)
  • ******
  • Forum Posts:
    • Melbourne, Vic
Re: Police force GI issues
« Reply #10 on: September 29, 2015, 12:14:09 AM »
really strange fault or faults you have. (sounds like i am imitating Yoda)
if you have flippers and F4 is ok then you should have at least the left and right slingshots.
check F1, F2A, F2C and F3.
are all the flashers working of just some?
one last thing i need you to do is when in coil test take note if any flashers are flashing when the test display shows a solenoid should be firing.
   
Logged
On site pinball repairs in MELBOURNE NTH SUBURBS  : Circuit board repairs and refurbishing Australia wide (via Aust post)

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re:
« Reply #11 on: September 29, 2015, 12:21:36 AM »
Sling shots work. Sorry should have said that
Logged

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re:
« Reply #12 on: September 29, 2015, 12:24:31 AM »
In tests all A's seem not to work but C's work. (Solenoid test)
Logged

Offline beaky

  • Trade Count: (+7)
  • ******
  • Forum Posts:
    • Melbourne, Vic
Re: Police force GI issues
« Reply #13 on: September 29, 2015, 12:54:29 AM »
if this has happened  after you worked on the interconnect board then you may have disturbed some of the wires in a connector and they are no longer connecting or you may have some dry joints on the inter connector board
   
Logged
On site pinball repairs in MELBOURNE NTH SUBURBS  : Circuit board repairs and refurbishing Australia wide (via Aust post)

Offline beaky

  • Trade Count: (+7)
  • ******
  • Forum Posts:
    • Melbourne, Vic
Re: Police force GI issues
« Reply #14 on: September 29, 2015, 01:29:33 AM »
or coincidentally you have a problem with  the A/C relay on the Aux driver board, 
 
Logged
On site pinball repairs in MELBOURNE NTH SUBURBS  : Circuit board repairs and refurbishing Australia wide (via Aust post)
Pages: [1] 2   Go Up
« previous next »