« previous next »
Pages: [1] 2   Go Down

Author Topic: SWEP1  (Read 1428 times)

0 Members and 6 Guests are viewing this topic.

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
SWEP1
« on: December 19, 2015, 04:41:39 PM »
Hey guys haven't played this in a while.  Turned it on and it shoots 2 balls into the shooter lane instead of 1.
Logged

Offline Steevsee

  • Trade Count: (+1)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Brisbane
Re: SWEP1
« Reply #1 on: December 19, 2015, 05:40:11 PM »
Check/clean trough opto switches.
Logged

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re: SWEP1
« Reply #2 on: December 19, 2015, 06:23:29 PM »
Done that. Noticed in switch test there is a trough jam
Logged

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re: SWEP1
« Reply #3 on: December 19, 2015, 06:25:56 PM »
Logged

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re:
« Reply #4 on: December 19, 2015, 06:27:15 PM »
Not sure if this has anything to do with it. Tried emptying balls and putting them back. Opto responds when I do this
Logged

Offline Steevsee

  • Trade Count: (+1)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Brisbane
Re: SWEP1
« Reply #5 on: December 19, 2015, 07:30:03 PM »
So opto 41 is changing state when activated in switch test?
Logged

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re:
« Reply #6 on: December 19, 2015, 07:53:57 PM »
Not sure how to active it
 But when I block opto 4 it won't change state in test. I reckon dodgy opto
Logged

Offline Steevsee

  • Trade Count: (+1)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Brisbane
Re: SWEP1
« Reply #7 on: December 19, 2015, 09:11:21 PM »
Most likely a bad opto.

You can check opto transmitter side by looking through a digital camera.   Lit optos will show up when viewed through the camera.
Logged

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re:
« Reply #8 on: December 19, 2015, 11:12:42 PM »
Transmitter side looks fine must be other side
Logged

Offline Steevsee

  • Trade Count: (+1)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Brisbane
Re: SWEP1
« Reply #9 on: December 20, 2015, 03:13:49 PM »
Test receiver opto with a torch light(non led) directed at receiver whilst in switch test.
Logged

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re:
« Reply #10 on: December 20, 2015, 05:10:47 PM »
Ok i shall try.
Logged

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re:
« Reply #11 on: December 24, 2015, 09:21:15 PM »
Ball 4 opto remains open and doesn't respond
Logged

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re:
« Reply #12 on: January 03, 2016, 05:21:35 PM »
Replaced opto transmitter and it now works.
Thanks to all
Logged

Offline infinite1977

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Lower Templestowe
  • Roger 504 apprehend him
Re:
« Reply #13 on: January 29, 2016, 04:15:31 PM »
Damm opto playing up again. Must be receiver side.
Logged

Offline DSB

  • Trade Count: (0)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Gold Coast
    • OMNI Electrical & Data
Re:
« Reply #14 on: January 29, 2016, 05:04:42 PM »
Quote from: infinite1977 on January 29, 2016, 04:15:31 PM
Damm opto playing up again. Must be receiver side.

Dry solder joint on the board maybe?
Logged
Pages: [1] 2   Go Up
« previous next »