Author Topic: Charlies Angels Pop Bumpers  (Read 4458 times)

0 Members and 1 Guest are viewing this topic.

Offline Pinballrocks

  • Trade Count: (0)
  • ****
  • Forum Posts:
  • sydney
Charlies Angels Pop Bumpers
« on: July 10, 2021, 11:49:20 AM »
Hi All,


Im hoping someone can point me in the right direction.
I have always had very weak pop bumpers on my Charlies Angles.
I have cleaned all contacts and lubricated all metal pivot points.


Is there something else i should be checking or doing?


Hoping someone can shed some light


Cheers Paul
:) :)      PAUL     :):)

Offline Strangeways

  • Pinball Restoration is my passion
  • Administrator
  • Trade Count: (+9)
  • *****
  • High Score Initials:
  • Forum Posts:
  • Melbourne
  • ABN 68 283 634 461
    • Ride The Boney Beast
Re: Charlies Angels Pop Bumpers
« Reply #1 on: July 10, 2021, 04:03:27 PM »
First thing - Never lubricate moving parts on a SS and later machine. The pop bumper could be weak due to the coil sleeve, worn plunger or years of lubrication. Check to see if the rod and ring moves up and down without any friction. Then clean the plungers and replace the coil sleeves.


Before any of this, ensure the gap is correct on the switch, and that the spoon is correctly aligned with the pop bumper skirt.
Aussie Pinball - Proud to be Australia's Premier Pinball Forum

http://www.australianpinballrestorations.com.au/

http://www.rtbb.com.au/catalog/

We carry the largest range of NEW Ramps in Australia

Offline Pinballrocks

  • Trade Count: (0)
  • ****
  • Forum Posts:
  • sydney
Re: Charlies Angels Pop Bumpers
« Reply #2 on: July 10, 2021, 06:00:11 PM »

Thanks I will check this out as soon as i get a chance. :-)


:) :)      PAUL     :):)

Offline Quench

  • Trade Count: (0)
  • **
  • Forum Posts:
Re: Charlies Angels Pop Bumpers
« Reply #3 on: July 12, 2021, 02:09:13 AM »

I have always had very weak pop bumpers on my Charlies Angles.

From memory the Gottlieb pop bumper rods on their rings were about 1/8" longer than other manufacturers. When people mistakenly replace the ring/rods with shorter versions the consequence is weak pop bumper action because the ball doesn't go under the ring deep enough when the switch activates.
If you have another game, compare where the ball touches the pop bumper ring.

Offline Pinballrocks

  • Trade Count: (0)
  • ****
  • Forum Posts:
  • sydney
Re: Charlies Angels Pop Bumpers
« Reply #4 on: July 12, 2021, 09:29:11 PM »
 will do thanks

:) :)      PAUL     :):)

Offline Pinballrocks

  • Trade Count: (0)
  • ****
  • Forum Posts:
  • sydney
Re: Charlies Angels Pop Bumpers
« Reply #5 on: October 05, 2021, 07:33:19 PM »
Update on C/A.
I have found that the Pop bumper rings are not returning to top of pop bumper either too short or rubbing on playfield so thanks for all your feedback i will sort it out soon
:) :)      PAUL     :):)

Offline Strangeways

  • Pinball Restoration is my passion
  • Administrator
  • Trade Count: (+9)
  • *****
  • High Score Initials:
  • Forum Posts:
  • Melbourne
  • ABN 68 283 634 461
    • Ride The Boney Beast
Re: Charlies Angels Pop Bumpers
« Reply #6 on: October 06, 2021, 08:20:25 PM »
If the Rods on the Rings are rubbing the side of the playfield - loosen the 3 screws that hold the pop bumper bracket and move it around until there is no friction - and then tighten.
Aussie Pinball - Proud to be Australia's Premier Pinball Forum

http://www.australianpinballrestorations.com.au/

http://www.rtbb.com.au/catalog/

We carry the largest range of NEW Ramps in Australia

Offline Pinballrocks

  • Trade Count: (0)
  • ****
  • Forum Posts:
  • sydney
Re: Charlies Angels Pop Bumpers
« Reply #7 on: October 06, 2021, 08:58:46 PM »
 Ok I will give that a try.
 Thanks

:) :)      PAUL     :):)

Offline Pinballrocks

  • Trade Count: (0)
  • ****
  • Forum Posts:
  • sydney
Re: Charlies Angels Pop Bumpers
« Reply #8 on: October 06, 2021, 10:02:18 PM »
 
I have loosened the screws on the brackets and rods are now everything is clear of playfield.
The pop bumpers are still very weak. They are so weak that i can almost hold the ball on the skirt and the ring is too weak to kick it out of my hand.
Not sure what else to do at this stage?
:) :)      PAUL     :):)