« previous next »
Pages: 1 [2] 3   Go Down

Author Topic: E.M.s arn't that hard to work on after all  (Read 938 times)

0 Members and 15 Guests are viewing this topic.

Offline beaky

  • Trade Count: (+7)
  • ******
  • Forum Posts:
    • Melbourne, Vic
Re: E.M.s arn't that hard to work on after all
« Reply #15 on: January 05, 2012, 09:18:23 PM »
Quote from: GORGAR 1 on January 05, 2012, 07:32:28 PM
Good stuff another EM tech you have to be careful not to zap yourself don't you that's what I here anyways

Peter
Been there done that, a few months ago I touched one of the terminals on the big 120 volt coil for the reset bar on the GTB. even with the power switch under the machine turned off it still gave me a big boot  ^.^
I can't understand why, it should be turned off when the power switch under the machine is switched off, I would have to look at the schematics for the machine (which I don't have) to work out why and if it should still be live with the switch turned off.
There was a lot of swearing and cursing when it happened.
After that incident i now do all my work on EM's with it unplugged from the mains  !@)
« Last Edit: January 05, 2012, 09:23:32 PM by beaky »
Logged
On site pinball repairs in MELBOURNE NTH SUBURBS  : Circuit board repairs and refurbishing Australia wide (via Aust post)

Offline pinnies4me

  • Administrator
  • Trade Count: (+5)
  • *****
  • High Score Initials:
  • Forum Posts:
    • Victoria
Re: E.M.s arn't that hard to work on after all
« Reply #16 on: January 05, 2012, 09:26:30 PM »
Same with Gottlieb System 1 and 80 - they are still live at the transformer when plugged in, learned to unplug them a long time back (drop  a screwdriver or let the solder wire drop and you work it out quickly!!) Never really found if it's the same with other manufacturers (as other makers put their high power stuff in less accessible areas, probably for good reason)
Logged
“If you wanna escape, go up to a pinball machine. There’s a magic button on the front that takes you to a world under the glass and makes the the rest of the universe disappear.”

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Re: E.M.s arn't that hard to work on after all
« Reply #17 on: January 05, 2012, 09:30:13 PM »
Quote from: beaky on January 05, 2012, 09:18:23 PM
Quote from: GORGAR 1 on January 05, 2012, 07:32:28 PM
Good stuff another EM tech you have to be careful not to zap yourself don't you that's what I here anyways

Peter
Been there done that, a few months ago I touched one of the terminals on the big 120 volt coil for the reset bar on the GTB. even with the power switch under the machine turned off it still gave me a big boot  ^.^
I can't understand why, it should be turned off when the power switch under the machine is switched off, I would have to look at the schematics for the machine (which I don't have) to work out why and if it should still be live with the switch turned off.
There was a lot of swearing and cursing when it happened.
After that incident i now do all my work on EM's with it unplugged from the mains  !@)


Yes... is not a mains switch, is only from transformer to coils... touch either side of transformer and you know it

If I had known who was making the offer I would have left it alone.


Nah... i emailed him and pointed out that it didnt work, back door was missing and had wear... i put that into unseen project catagory and so $350 was my offer.... its now working and so typically, my interest has vanished!
« Last Edit: January 05, 2012, 09:33:11 PM by Retropin »
Logged

Offline swinks

  • Trade Count: (+18)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Lake Macquarie, NSW
Re: E.M.s arn't that hard to work on after all
« Reply #18 on: January 05, 2012, 10:29:14 PM »
That's awesome beaky, I have a Surf Champ waiting to do a restore along with a full clean and set - gives me some encouragement.
Logged
https://swinks.com.au

for pinball parts (reproduction & mods)
for pinball t-shirts

Offline Olivia_jason

  • Trade Count: (+2)
  • ******
  • Forum Posts:
Re: E.M.s arn't that hard to work on after all
« Reply #19 on: January 05, 2012, 10:36:06 PM »
on that subject of Gtb's being live at transformer even switched off, are they using a fair wack of power?? i might have to turn mine off at the wall at my shop if that is the case. any ideas on that?
Logged

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Re: E.M.s arn't that hard to work on after all
« Reply #20 on: January 05, 2012, 10:49:01 PM »
No... there is no current flow until you either turn it on or touch the transformer output
Logged

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Re: E.M.s arn't that hard to work on after all
« Reply #21 on: January 12, 2012, 04:12:48 PM »
Oi...Beaky.

See what youve done??? 1 more week and this would have been listed down to $350 and i would have snapped it up...

http://www.ebay.com.au/itm/Williams-1977-HOT-TIP-electro-mechanical-/250970933693?pt=AU_CoinOp&hash=item3a6f0889bd

Logged

Offline goodolddays

  • Trade Count: (0)
  • ******
  • Forum Posts:
    • Riverstone NSW
Re: E.M.s arn't that hard to work on after all
« Reply #22 on: January 12, 2012, 04:53:04 PM »
Seller forgot use the word "Rare"   :lol :lol
Logged
I need more room ! and more $$$

Offline beaky

  • Trade Count: (+7)
  • ******
  • Forum Posts:
    • Melbourne, Vic
Re: E.M.s arn't that hard to work on after all
« Reply #23 on: January 12, 2012, 07:37:26 PM »
Quote from: Retropin on January 12, 2012, 04:12:48 PM
Oi...Beaky.

See what youve done??? 1 more week and this would have been listed down to $350 and i would have snapped it up...

http://www.ebay.com.au/itm/Williams-1977-HOT-TIP-electro-mechanical-/250970933693?pt=AU_CoinOp&hash=item3a6f0889bd


I can't win can I. He said he would keep it if I got it going  ^.^  Bet his missus nagged him into selling It. thats why he sold his Flinstones  #@#
Logged
On site pinball repairs in MELBOURNE NTH SUBURBS  : Circuit board repairs and refurbishing Australia wide (via Aust post)

Offline roundball

  • Trade Count: (0)
  • ****
  • Forum Posts:
    • BNE - The only place to be.
Re: E.M.s arn't that hard to work on after all
« Reply #24 on: January 13, 2012, 09:49:27 PM »
Thanks Beaky..  You gave me the inspiration to tackle my EM problems the other day and low and behold she's working a treat..

Big call out to Gav too for the help he offered via PM, it all adds up and she's flippin' nice now.  :)
Logged

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Re: E.M.s arn't that hard to work on after all
« Reply #25 on: January 13, 2012, 10:23:21 PM »
Quote from: roundball on January 13, 2012, 09:49:27 PM
Thanks Beaky..  You gave me the inspiration to tackle my EM problems the other day and low and behold she's working a treat..

Big call out to Gav too for the help he offered via PM, it all adds up and she's flippin' nice now.  :)



Awesome to hear!!!
Logged

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Re: E.M.s arn't that hard to work on after all
« Reply #26 on: January 19, 2012, 11:33:32 AM »
Quote from: roundball on January 13, 2012, 09:49:27 PM
Thanks Beaky..  You gave me the inspiration to tackle my EM problems the other day and low and behold she's working a treat..

Big call out to Gav too for the help he offered via PM, it all adds up and she's flippin' nice now.  :)


...and now your giving her the flip!
Logged

Offline pinballowner

  • Trade Count: (0)
  • ***
  • Forum Posts:
    • Qld south of Brisbane
Re: E.M.s arn't that hard to work on after all
« Reply #27 on: February 02, 2012, 10:55:11 PM »
Logged

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Re: E.M.s arn't that hard to work on after all
« Reply #28 on: February 03, 2012, 06:33:06 AM »
Got to love the questions on that one..
Logged

Offline Homepin

  • Trade Count: (+15)
  • ******
  • Forum Posts:
  • Not a business - A Passion!
Re: E.M.s arn't that hard to work on after all
« Reply #29 on: February 03, 2012, 12:16:37 PM »
Quote from: Retropin on February 03, 2012, 06:33:06 AM
Got to love the questions on that one..

This listing was ended by the seller because the item is no longer available
Logged
Replacement Pinball PCBs that remain faithful to the originals
Pages: 1 [2] 3   Go Up
« previous next »