« previous next »
Pages: [1] 2   Go Down

Author Topic: Indiana Jones -Mini Playfield  (Read 4027 times)

0 Members and 3 Guests are viewing this topic.

Offline VanillaSlicePie

  • Trade Count: (0)
  • ***
  • Forum Posts:
Indiana Jones -Mini Playfield
« on: December 19, 2016, 02:05:41 PM »
Giday
Mini playfield faulty only in gameplay not in diagnostic mode. Have cleaned optics. Made a slight improvement. So question is...where in Aussie land can i purchase the left and right flipper "U" optos besides Pinball spare parts which are out of stock?

Cheers
Logged

Offline robm

  • Trade Count: (+1)
  • ******
  • Forum Posts:
    • Townsville
Re:
« Reply #1 on: December 19, 2016, 08:48:25 PM »
If it works consistently in test its likely not the optos. Is the set screw tight on the shaft that rotates the mini pf? If its loose or off centre it will cause issues

Sent from my SM-G930F using Tapatalk
Logged

Offline VanillaSlicePie

  • Trade Count: (0)
  • ***
  • Forum Posts:
Re: Indiana Jones -Mini Playfield
« Reply #2 on: December 19, 2016, 08:54:50 PM »
Mmm will check that.
Cheers Rob
Logged

Offline VanillaSlicePie

  • Trade Count: (0)
  • ***
  • Forum Posts:
Re: Indiana Jones -Mini Playfield
« Reply #3 on: December 20, 2016, 12:04:02 PM »
Set screw is tight, slight bit of play when moving mini play field by hand. I guess that's normal wear and tear! The issue is the tilt to the left only. It stutters and is not a smooth action. Have cleaned all optos. Any other handy hints?? I'm still thinking maybe left flipper opto....
Logged

Offline Dann36

  • Trade Count: (+1)
  • ***
  • Forum Posts:
Re: Indiana Jones -Mini Playfield
« Reply #4 on: December 20, 2016, 03:37:35 PM »


If it works fine in test then most likely its the flipper opto, if its just left tilt then swap the opto's from left to right and see if the fault follows..

Test mode works because you use the test switches to run the motor....In game you use the  flipper buttons..
Logged

Offline VanillaSlicePie

  • Trade Count: (0)
  • ***
  • Forum Posts:
Re: Indiana Jones -Mini Playfield
« Reply #5 on: December 20, 2016, 06:46:37 PM »
Originally gonna do that however the left flipper opto is different from the right.
« Last Edit: December 20, 2016, 07:11:15 PM by VanillaSlicePie »
Logged

Offline Boots

  • Trade Count: (+8)
  • ******
  • Forum Posts:
    • Adelaide
Re: Indiana Jones -Mini Playfield
« Reply #6 on: December 20, 2016, 07:12:58 PM »
Quote from: VanillaSlicePie on December 20, 2016, 06:46:37 PM
Originally gonna do that however the left flipper opto is different from the right.

How?
pics?
Logged

Offline VanillaSlicePie

  • Trade Count: (0)
  • ***
  • Forum Posts:
Re: Indiana Jones -Mini Playfield
« Reply #7 on: December 20, 2016, 10:14:36 PM »
Refering to manual and pics looks like the left one is original and right one is not.
Logged

Offline VanillaSlicePie

  • Trade Count: (0)
  • ***
  • Forum Posts:
Re: Indiana Jones -Mini Playfield
« Reply #8 on: December 20, 2016, 10:26:42 PM »
Black plastic interrupter is original
Logged

Offline Boots

  • Trade Count: (+8)
  • ******
  • Forum Posts:
    • Adelaide
Re: Indiana Jones -Mini Playfield
« Reply #9 on: December 21, 2016, 08:41:24 AM »
Quote from: VanillaSlicePie on December 20, 2016, 10:26:42 PM
Black plastic interrupter is original
It shouldn't matter that they are different.
Have you checked them in the switch test?
You should see two switches switching for each flipper button, if not maybe that is your problem.
You may have a faulty opto on the board in that case
Looks like there are two different optos on the L/H flipper switch
« Last Edit: December 21, 2016, 08:43:20 AM by Boots »
Logged

Offline VanillaSlicePie

  • Trade Count: (0)
  • ***
  • Forum Posts:
Re: Indiana Jones -Mini Playfield
« Reply #10 on: December 21, 2016, 03:22:06 PM »
Tested good. Still leaning towards optos. Thoughts?
Logged

Offline Dann36

  • Trade Count: (+1)
  • ***
  • Forum Posts:
Re: Indiana Jones -Mini Playfield
« Reply #11 on: December 21, 2016, 05:48:23 PM »

It does not matter that they are different, the connector will be the same. Swap the boards around and if the opto is causing the trouble and most likely it is, the fault will move with the board.  I really doubt it will be anything else especially if in test it works fine..

Logged

Offline VanillaSlicePie

  • Trade Count: (0)
  • ***
  • Forum Posts:
Re: Indiana Jones -Mini Playfield
« Reply #12 on: December 21, 2016, 09:53:00 PM »
Okay, good news and bad news. Swapped opto boards and presto problem moved with the board so, left opto board is faulty. Still need to find replacement. Hard to find. Trying to avoid overseas suppliers oz dollar freight etc. And thanks heaps for all who helped. Much appreciated!  ^^^
Logged

Offline Boots

  • Trade Count: (+8)
  • ******
  • Forum Posts:
    • Adelaide
Re: Indiana Jones -Mini Playfield
« Reply #13 on: December 21, 2016, 10:05:04 PM »
Quote from: VanillaSlicePie on December 21, 2016, 09:53:00 PM
Okay, good news and bad news. Swapped opto boards and presto problem moved with the board so, left opto board is faulty. Still need to find replacement. Hard to find. Trying to avoid overseas suppliers oz dollar freight etc. And thanks heaps for all who helped. Much appreciated!  ^^^

You can change the faulty opto for this:
http://au.rs-online.com/web/p/slotted-optical-switches/7085538/

or buy a pair of new boards here:
http://www.johns-arcade.com/product-page/74eacd86-ba69-615b-5046-8db07256a378

with new actuators from here:
http://www.pinballspareparts.com.au/03-9001-2.html
Logged

Offline VanillaSlicePie

  • Trade Count: (0)
  • ***
  • Forum Posts:
Re: Indiana Jones -Mini Playfield
« Reply #14 on: December 22, 2016, 10:36:21 AM »
Awesome! So much help on this site. Thanks again.  $#$
Logged
Pages: [1] 2   Go Up
« previous next »