« previous next »
Pages: [1]   Go Down

Author Topic: Slow lazy flipper action  (Read 351 times)

0 Members and 3 Guests are viewing this topic.

Offline pinball god

  • Trade Count: (+1)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Melbourne
  • Metallica is here to stay
Slow lazy flipper action
« on: May 12, 2011, 03:48:23 PM »
I have a flipper that worked fine and after a few games started to move slowly to not at all. After a power off for awhile, I worked ok then started to slow up etc etc. Today I powered on and it's moving slow from the beginning. It does reach full stroke on occasions and can be held there. I've checked for any binding and seems ok. I also tried pressing the flipper while the pf was up and saw it labour in it's movement and when I gave it a little assistance it seemed to energize quickly and get to end if stroke.

Any ideas?
Logged
Still loving my Metallica Premium

Offline beaky

  • Trade Count: (+7)
  • ******
  • Forum Posts:
    • Melbourne, Vic
Re: Slow lazy flipper action
« Reply #1 on: May 12, 2011, 04:22:02 PM »
what machine is it on?
i would check the eos switch and the coil itself. depending on what machine its it may have one or two windings (2 tabs is one winding, 3 tabs is 2 windings). if it has 2 windings then the hold winding is working fine but the high power winding is not working
« Last Edit: May 12, 2011, 04:26:53 PM by beaky »
Logged
On site pinball repairs in MELBOURNE NTH SUBURBS  : Circuit board repairs and refurbishing Australia wide (via Aust post)

Offline pinball god

  • Trade Count: (+1)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Melbourne
  • Metallica is here to stay
Re: Slow lazy flipper action
« Reply #2 on: May 12, 2011, 05:33:43 PM »
Hi beaky, it's a non fliptronics style. T2 machine, it has 3 tabs. So are you saying the coil is stuffed? If so should I also check the eos before replacing to avoid stuffing the new one?
« Last Edit: May 12, 2011, 05:36:45 PM by pinball god »
Logged
Still loving my Metallica Premium

Offline 48

  • Trade Count: (+2)
  • *****
  • Forum Posts:
Re: Slow lazy flipper action
« Reply #3 on: May 12, 2011, 06:17:41 PM »
I think he is saying check the EOS switch first. Appears that HP stroke is missing. Could be as simple as a dirty EOS switch.
Logged
Lets go Brandon!

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Re: Slow lazy flipper action
« Reply #4 on: May 12, 2011, 06:21:55 PM »
Gunk in the sleeve... bet its been sprayed with CRC or similar
Logged

Offline beaky

  • Trade Count: (+7)
  • ******
  • Forum Posts:
    • Melbourne, Vic
Re: Slow lazy flipper action
« Reply #5 on: May 12, 2011, 06:26:28 PM »
Quote from: Retropin on May 12, 2011, 06:21:55 PM
Gunk in the sleeve... bet its been sprayed with CRC or similar
Just make sure the eos is closing and opening properly and check that it is not badly pitted or worn out. There is no harm in replacing the eos at the same time as the coil. also make sure the yellow capacitor is soldered on properly also, this capacitor helps to extend the life of the eos.

And +1 on retropin's comment, could just be full of gunk.
Logged
On site pinball repairs in MELBOURNE NTH SUBURBS  : Circuit board repairs and refurbishing Australia wide (via Aust post)

Offline 48

  • Trade Count: (+2)
  • *****
  • Forum Posts:
Re: Slow lazy flipper action
« Reply #6 on: May 12, 2011, 06:31:53 PM »
Quote from: Retropin on May 12, 2011, 06:21:55 PM
Gunk in the sleeve... bet its been sprayed with CRC or similar
Never even thought of that! People put CRC on flipper plungers?   *!@
Logged
Lets go Brandon!

Offline beaky

  • Trade Count: (+7)
  • ******
  • Forum Posts:
    • Melbourne, Vic
Re: Slow lazy flipper action
« Reply #7 on: May 12, 2011, 06:44:47 PM »
Quote from: 48 on May 12, 2011, 06:31:53 PM
Quote from: Retropin on May 12, 2011, 06:21:55 PM
Gunk in the sleeve... bet its been sprayed with CRC or similar
Never even thought of that! People put CRC on flipper plungers?   *!@
yep, its like putting an egg in a leaky radiator to fix your car. It might help it for a while but it will end up clogging everything  up with crap.  *.*
Logged
On site pinball repairs in MELBOURNE NTH SUBURBS  : Circuit board repairs and refurbishing Australia wide (via Aust post)

Offline Boots

  • Trade Count: (+8)
  • ******
  • Forum Posts:
    • Adelaide
Re: Slow lazy flipper action
« Reply #8 on: May 12, 2011, 08:44:31 PM »
Quote from: 48 on May 12, 2011, 06:31:53 PM
Quote from: Retropin on May 12, 2011, 06:21:55 PM
Gunk in the sleeve... bet its been sprayed with CRC or similar
Never even thought of that! People put CRC on flipper plungers?   *!@
On one machine I found a few with axle grease on them!
Logged

Offline pinball god

  • Trade Count: (+1)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Melbourne
  • Metallica is here to stay
Re: Slow lazy flipper action
« Reply #9 on: May 12, 2011, 09:49:10 PM »
 Did all the checks and pulled out the coil. Found I couldn't get the sleeve out. Figured I had got real hot. Replaced coil and all good at the moment. Thanks for the suggestions
Logged
Still loving my Metallica Premium
Pages: [1]   Go Up
« previous next »