Author Topic: Clear Coating  (Read 980 times)

0 Members and 2 Guests are viewing this topic.

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Clear Coating
« on: November 23, 2008, 03:44:31 PM »
Walking round Bunnings today, i saw that they now carry an off the shelf clear coat. reading up on the product, it would seem ideal for pinball restoration. I havent tested the product yet, but will do as it seems applicable to almost any application. Bear in mind that when you mix up CC - you always over estimate the amount you will need - especially if using an airbrush, so the volumes sold at Bunnings are ideal.

This product 'MAY" be ideal for sealing those hot stamped drop targets also instead of the cheap looking Mylar.

Product can be viewed here

www.glasscoat.com.au/




Offline Strangeways

  • Pinball Restoration is my passion
  • Administrator
  • Trade Count: (+9)
  • *****
  • High Score Initials:
  • Forum Posts:
  • Melbourne
  • ABN 68 283 634 461
    • Ride The Boney Beast
Re: Clear Coating
« Reply #1 on: November 23, 2008, 04:19:55 PM »

Will you be trialling this product at any stage, Gavin ?
Aussie Pinball - Proud to be Australia's Premier Pinball Forum

http://www.australianpinballrestorations.com.au/

http://www.rtbb.com.au/catalog/

We carry the largest range of NEW Ramps in Australia

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Re: Clear Coating
« Reply #2 on: November 23, 2008, 05:03:27 PM »
Yes - ill buy the sample pack and put a mix of paints down - acrylic, std enamel etc - also marker pen and see the results. Ill also put some down over some black, let set and drop a pinball from a height on top of it.

Ill do this over and over and see if any "milking"occurs to the finish which would suggest stress

Offline MartyJ

  • Trade Count: (+4)
  • ******
  • High Score Initials:
  • Forum Posts:
  • Melbourne
Re: Clear Coating
« Reply #3 on: November 23, 2008, 05:12:12 PM »
I don't know how it would go on a PF -

"Glass Coat is best thought of as a pouring medium rather than a painting medium.
Flood the surface to be coated immediately. You should aim to pour all the batches (if you have mixed up several) in the first 5 minutes after mixing.
While Glass Coat can be applied with a brush, the best effect is achieved if it is poured over a level surface.
Use a disposable brush or spreader to touch up sides or to move Glass Coat across the surface.
It is important that the surface be as level as possible so that Glass Coat spreads evenly."

source: http://www.glasscoat.com.au/basics.shtml

Although may work with targets etc and other bits n pieces..

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Re: Clear Coating
« Reply #4 on: November 23, 2008, 05:45:34 PM »
Was going to trial it through an air brush - the thinner/ clean up solvent is also available.

Its completely fume free which is a real bonus!

stuba

  • Guest
  • Trade Count: (0)
Re: Clear Coating
« Reply #5 on: November 28, 2008, 11:54:39 AM »
keen to see how it goes. maybe it could be used for levelling insert concaves?

Offline Strangeways

  • Pinball Restoration is my passion
  • Administrator
  • Trade Count: (+9)
  • *****
  • High Score Initials:
  • Forum Posts:
  • Melbourne
  • ABN 68 283 634 461
    • Ride The Boney Beast
Re: Clear Coating
« Reply #6 on: November 28, 2008, 01:30:22 PM »
keen to see how it goes. maybe it could be used for levelling insert concaves?


Yes - That's what I'd like to know in the short term..
Aussie Pinball - Proud to be Australia's Premier Pinball Forum

http://www.australianpinballrestorations.com.au/

http://www.rtbb.com.au/catalog/

We carry the largest range of NEW Ramps in Australia

Offline Retropin

  • Trade Count: (+4)
  • ******
  • Forum Posts:
Re: Clear Coating
« Reply #7 on: November 28, 2008, 03:16:52 PM »
Stuba!!!

Mate, i had you in mind when i was posting this - may well be ideal,

will trial it this weekend



Offline Pinball Fixers

  • Trade Count: (0)
  • ******
  • Forum Posts:
  • Montrose, VIC
Re: Clear Coating
« Reply #8 on: January 31, 2009, 10:43:20 AM »
Hey Gav, how did the test for the Clearcoat go?

Offline Pinball Fixers

  • Trade Count: (0)
  • ******
  • Forum Posts:
  • Montrose, VIC
Re: Clear Coating
« Reply #9 on: January 31, 2009, 10:45:25 AM »
Forget that mate... just read your results thread #@#
http://aussiepinball.com/index.php?topic=404.0
« Last Edit: January 31, 2009, 11:20:28 AM by pinball-fixer »