« previous next »
Pages: [1]   Go Down

Author Topic: Wire-forms required  (Read 547 times)

0 Members and 4 Guests are viewing this topic.

Offline felixthadog

  • Trade Count: (0)
  • ******
  • Forum Posts:
    • Melbourne
Wire-forms required
« on: September 26, 2009, 01:42:15 PM »
Hi all,

I was wondering if a kind forum member could help me out? I need a couple of wire-forms for my Judge Dredd machine, nothing fancy but I don't have the skills or equipment to make them myself. Of course I will pay for materials, labour and postage, but I think it would be cheaper to do it this way then to order from the US.

The wire-forms I need are exactly like this:
http://bayareaamusements.com/Merchant2/merchant.mvc?Screen=PROD&Product_Code=MX-6466-5&Category_Code=WFM&Product_Count=54

One of the wire-forms needs to go to the right of the Subway scoop as seen here:



Cheers,
Matthew
« Last Edit: September 26, 2009, 01:45:52 PM by felixthadog »
Logged

Offline felixthadog

  • Trade Count: (0)
  • ******
  • Forum Posts:
    • Melbourne
Re: Wire-forms required
« Reply #1 on: September 28, 2009, 08:44:16 AM »
No takers?  *!@

I might have used the incorrect terminology, the "wire-forms" I require are actually "Ball guide metal rods".

Matthew
Logged

Offline Extra Ball

  • Read-Only
  • Trade Count: (0)
  • *
  • Forum Posts:
    • Newcastle
Re: Wire-forms required
« Reply #2 on: September 28, 2009, 09:31:18 AM »
Sum1 would have some outlane guide wire from an old PF that you could bend-up in a vice. You could prob do a decent job with pliers actually Matt. You can get a rounded cornerby by bending it over a piece of dowel.
« Last Edit: September 28, 2009, 09:32:50 AM by Extra Ball »
Logged

Offline felixthadog

  • Trade Count: (0)
  • ******
  • Forum Posts:
    • Melbourne
Re: Wire-forms required
« Reply #3 on: September 28, 2009, 03:29:18 PM »
Quote from: Extra Ball on September 28, 2009, 09:31:18 AM
Sum1 would have some outlane guide wire from an old PF that you could bend-up in a vice. You could prob do a decent job with pliers actually Matt. You can get a rounded cornerby by bending it over a piece of dowel.

That would do nicely Greg, I just hope somebody has some wire that they could part with  @@^

Matthew
Logged

Offline ddstoys

  • Trade Count: (+23)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Geelong
Re: Wire-forms required
« Reply #4 on: September 28, 2009, 03:53:22 PM »
Hi matt
       What are the hole to hole measurements and ill check some of my spare playfields for ya  ^^^
Logged

Offline felixthadog

  • Trade Count: (0)
  • ******
  • Forum Posts:
    • Melbourne
Re: Wire-forms required
« Reply #5 on: September 28, 2009, 05:16:56 PM »
Quote from: ddstoys on September 28, 2009, 03:53:22 PM
Hi matt
       What are the hole to hole measurements and ill check some of my spare playfields for ya  ^^^

Hi Daniel,

According to the link I posted in my original post, the rods are 1 1/4 inch. Unless I am mistaken, I think that is the distance between the 2 holes that the rod slots into.

Matthew
Logged

Offline ddstoys

  • Trade Count: (+23)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Geelong
Re: Wire-forms required
« Reply #6 on: September 28, 2009, 06:03:10 PM »
Ok ill take a look for some that size and let you know ^^^
Logged

Offline MartyJ

  • Trade Count: (+4)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Melbourne
Re: Wire-forms required
« Reply #7 on: September 28, 2009, 06:57:55 PM »
Matthew,

You can try your local bicycle store as they should sell bike spokes (about $1.00 each).  The size of these (diameter) should be close.
Logged

Offline ddstoys

  • Trade Count: (+23)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Geelong
Re: Wire-forms required
« Reply #8 on: September 28, 2009, 07:19:56 PM »
I just tried the bike spoke thing yesterday but they were to thin for the holes must see if i can get thicker ones
Logged

Offline Extra Ball

  • Read-Only
  • Trade Count: (0)
  • *
  • Forum Posts:
    • Newcastle
Re: Wire-forms required
« Reply #9 on: September 28, 2009, 07:24:33 PM »
Quote from: ddstoys on September 28, 2009, 07:19:56 PM
I just tried the bike spoke thing yesterday but they were to thin for the holes must see if i can get thicker ones

you see so many bikes thrown-out for kerb-side clean-up, maybe we should be grabbing the wheels
 :lol
Logged

Offline ddstoys

  • Trade Count: (+23)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Geelong
Re: Wire-forms required
« Reply #10 on: September 28, 2009, 07:48:37 PM »
Do these look like what your after Matt?

Send me a PM with your address and ill get em in the post if its what your after ^^^
Logged

Offline felixthadog

  • Trade Count: (0)
  • ******
  • Forum Posts:
    • Melbourne
Re: Wire-forms required
« Reply #11 on: September 28, 2009, 09:51:45 PM »
Quote from: ddstoys on September 28, 2009, 07:48:37 PM
Do these look like what your after Matt?

Send me a PM with your address and ill get em in the post if its what your after ^^^

Thanks Daniel, they look like the ones I need  *%* I'll PM you my address, and I can Paypal some money your way, just let me know the amount.

Matthew
Logged

Offline ddstoys

  • Trade Count: (+23)
  • ******
  • High Score Initials:
  • Forum Posts:
    • Geelong
Re: Wire-forms required
« Reply #12 on: October 01, 2009, 05:57:01 PM »
Hey Matt i got your Wire forms in the post today  ^^^
Logged

Offline felixthadog

  • Trade Count: (0)
  • ******
  • Forum Posts:
    • Melbourne
Re: Wire-forms required
« Reply #13 on: October 01, 2009, 07:33:08 PM »
Quote from: ddstoys on October 01, 2009, 05:57:01 PM
Hey Matt i got your Wire forms in the post today  ^^^

Awesome, thanks Daniel!  @@*

Matthew
Logged
Pages: [1]   Go Up
« previous next »